Repair TipsLocal Guides

Why is my toilet running constantly and how to fix it

A toilet that runs constantly is usually one worn part: the flapper, the fill valve, or the chain between them. Here is how to find which one it is and fix it.

9 min read
A toilet tank with the lid off in a Cleveland, Texas bathroom, showing the flapper and fill valve that cause a running toilet.

A running toilet is easy to ignore because it is quiet and the water goes down the drain, but it wastes a large amount of water over days and weeks, enough to show up on the next water bill. The good news is that almost every running toilet has one of three causes, and all three are inside the tank, where you can see them. This guide walks through the diagnosis in order, from the most common cause to the least, and ends with the point where a repair stops being a parts swap and starts being a plumber's job.

The flapper: the most common cause

The flapper is the rubber disc at the bottom of the tank that lifts when you flush and seals the tank afterwards. Over time it warps, hardens, or grows mineral deposits, and then it no longer seals: water leaks from the tank into the bowl, the water level drops, and the fill valve tops it up again, over and over. Lift the tank lid and watch: if the water level drops slowly without a flush, the flapper is leaking. Press down on the flapper with your hand: if the running stops, the flapper is the problem. Replacing it is a simple job: turn off the water at the valve behind the toilet, unhook the old flapper, take it with you to match it, and hook the new one on. If the flush valve seat underneath is pitted or corroded, a new flapper will not seal, and the seat or the valve needs attention.

The fill valve: the second suspect

The fill valve is the tall assembly on the left side of the tank that refills it after a flush. If it is set too high, water runs into the overflow tube constantly. If its seal is worn, it never shuts off fully and hisses or runs without stopping. Check the water level: it should sit below the top of the overflow tube, usually marked on the inside of the tank or the tube itself. If the level is above the tube, lower the float or the adjustment screw. If the valve keeps running with the float lifted by hand, the valve seal is worn and the fill valve needs replacing. A fill valve replacement is a straightforward job, but it means shutting off the water and working inside the tank, so take your time.

The chain: the small cause that fools everyone

The chain connects the flush handle to the flapper, and it has to have a little slack: about half an inch. If the chain is too short, it holds the flapper slightly open and the toilet runs. If it is too long, it tangles under the flapper and holds it open the same way. If the chain is kinked or corroded, it can catch and fail to let the flapper close. Adjust the chain so it has a small amount of slack and hangs free, and replace it if it is kinked or rusted. Check the flush handle too: a handle that sticks in the down position holds the flapper open, and a new handle is a small fix.

The dye test: proof in ten minutes

If you cannot see the cause, run a dye test. Put a few drops of food colouring in the tank, wait ten minutes without flushing, and look in the bowl. If colour appears in the bowl, water is leaking from the tank into the bowl, which points to the flapper or the flush valve seat. If no colour appears and the toilet still runs, the fill valve is the likely cause, because water is going into the overflow tube instead. The dye test costs nothing and settles the question before you buy parts.

When to call a plumber

Call a plumber if a new flapper and a new fill valve do not stop the running, if the flush valve seat is pitted or cracked, if the tank itself is cracked, or if the shutoff valve behind the toilet will not turn or leaks. Call too if the toilet rocks on the floor or leaks at the base, which is a different problem from a running toilet and usually means the wax seal has failed. A running toilet that has been running for weeks can also mask a larger water problem, so if your water bill jumped at the same time, read the water bill guide alongside this one. Our toilet repair and installation team handles flappers, fill valves, and flush valve seats, and our leak detection service can check whether the water loss is confined to the toilet. Homeowners in Grand Oaks Reserve with new toilets should know that even a new flapper can fail early if the water leaves deposits on the seal.

Frequently Asked Questions

Why is my toilet running constantly?

Usually a worn flapper that no longer seals, a fill valve set too high or with a worn seal, or a chain that is too short, too long, or tangled. The dye test shows whether water is leaking from the tank into the bowl.

How do I know if the flapper is bad?

Watch the tank water level: if it drops slowly without a flush, the flapper is leaking. Press down on the flapper: if the running stops, the flapper is the problem.

What is the dye test for a running toilet?

Put a few drops of food colouring in the tank, wait ten minutes without flushing, and look in the bowl. Colour in the bowl means water is leaking past the flapper or the flush valve seat.

Can a running toilet make my water bill go up?

Yes. A toilet that runs constantly wastes a large amount of water over days and weeks, and the increase shows up on the next water bill. Fix it as soon as you find it.

When should I call a plumber for a running toilet?

If a new flapper and fill valve do not stop it, if the flush valve seat is pitted or cracked, if the tank is cracked, or if the toilet rocks or leaks at the base.

Get help with plumbing in Cleveland

If a toilet in your Cleveland home keeps running after a new flapper and fill valve, call Precision Plumbing LLC at (346) 687-0011 during business hours, Monday through Saturday, 7:00 AM to 5:30 PM.

Tagged withrunning toilettoilet repaircleveland txflapperplumbing maintenance

A few answers before you start.

Short answers for the first few minutes. The team can cover the rest.

Still have a question?

Describe what you are seeing and we will point you to the right next step.

(346) 687-0011

Usually a worn flapper that no longer seals, a fill valve set too high or with a worn seal, or a chain that is too short, too long, or tangled. The dye test shows whether water is leaking from the tank into the bowl.

Watch the tank water level: if it drops slowly without a flush, the flapper is leaking. Press down on the flapper: if the running stops, the flapper is the problem.

Put a few drops of food colouring in the tank, wait ten minutes without flushing, and look in the bowl. Colour in the bowl means water is leaking past the flapper or the flush valve seat.

Yes. A toilet that runs constantly wastes a large amount of water over days and weeks, and the increase shows up on the next water bill. Fix it as soon as you find it.

If a new flapper and fill valve do not stop it, if the flush valve seat is pitted or cracked, if the tank is cracked, or if the toilet rocks or leaks at the base.

Need a running toilet fixed in Cleveland?

(346) 687-0011

Call Precision Plumbing LLC during business hours, Monday through Saturday, 7:00 AM to 5:30 PM. We find the cause, fix it, and test the toilet before we leave.

Call now(346) 687-0011